91视频麻豆视频,亚洲性一区,日韩高清在线播放不卡,99毛片,亚洲国产精品久久久久网站,一区二区高清视频,91精品一区二区三区久久久久

會員登錄
請登錄您的生意號,獲取電子名片。便于轉發分享!
取消
Tianda News
會員登錄
請登錄您的生意號,獲取電子名片。便于轉發分享!
取消
Coal burning boiler ZDFR
Coal burning boiler ZDFR
Product Category:Hot blast stove series
Fluidized bed coal-fired hot blast furnace (abbreviated as boiling furnace), its combustion mode is that the coal is broken into particles less than 10mm, through the coal feeder uniform speed into the furnace fluidized bed; The high pressure wind of the blower is shot into the belly of the furnace through the isobaric bellows from the numerous holes of the hood on the air distribution plate, and the scattered wind is aggregated into the "air cushion" to hold up the coal particles and the charge is fluidized boiling combustion. The coal particles and slag jump at high temperature, friction, collision and cracking, from large to small until burned out; This kind of combustion has the characteristics of large contact area between air and fuel, high relative motion speed, long residence time of fuel in the fluidized bed, fast combustion speed, high degree of burnout, energy saving and environmental protection. Therefore, it has been widely used and developed rapidly in industrial kiln.
Product Introduction

1.Product introduction

Fluidized bed coal-fired hot blast furnace (abbreviated as boiling furnace), its combustion mode is that the coal is broken into particles less than 10mm, through the coal feeder uniform speed into the furnace fluidized bed; The high pressure wind of the blower is shot into the belly of the furnace through the isobaric bellows from the numerous holes of the hood on the air distribution plate, and the scattered wind is aggregated into the "air cushion" to hold up the coal particles and the charge is fluidized boiling combustion. The coal particles and slag jump at high temperature, friction, collision and cracking, from large to small until burned out; This kind of combustion has the characteristics of large contact area between air and fuel, high relative motion speed, long residence time of fuel in the fluidized bed, fast combustion speed, high degree of burnout, energy saving and environmental protection. Therefore, it has been widely used and developed rapidly in industrial kiln.

2.Fluidized bed uses

Boiling furnace can be used for rotary dryer, vertical dryer, hammer dryer, indirect dryer, slag micro powder vertical mill, air sweep coal mill or coal powder vertical mill, fertilizer slurry granulator, powder drying tower, waste heat generation heat, material frying pan machine, all kinds of semi-finished product dryer and other equipment heating; Can be widely used in industrial raw materials or products drying, roasting. Such as: slag, clay, sludge, calcium carbide slag, compound fertilizer, industrial gypsum, gypsum board, iron fine powder, quartz sand, yellow sand, laterite ore, sulfur concentrate, siderite, zinc leaching slag, white carbon black, coke, coal powder and slime, etc.

3.Main performance and characteristics

1.Wide fuel adaptability, combustible value of more than 6270kJ/kg (1500kcal/kg) of all kinds of bituminous coal, anthracite, and even coal liver stone, chain row furnace slag, oil shale, coal slime, biomass fuel;
2.Furnace combustion temperature (850~1100t), uniform operating temperature, stable heating;
3.High combustion efficiency, burnout rate can reach more than 99%, furnace thermal efficiency is greater than 94%;
4.Easy ignition, long compression time, intermittent compression fire up to 16~48 hours, no need to reignite the furnace;
5.The outlet temperature of hot flue gas can be adjusted, the heating load can be adjusted broadly, and the outlet orientation of heating flue gas pipeline is flexible.
6.Ash slag carbon content < 1%, not easy to soften or bond, good activity, suitable for use as cement mixing material, easy to comprehensive utilization;
7.Clean combustion, low nitrogen oxide content in the flue gas, low cost curing desulfurization can be used in the furnace, so that the sulfur in the coal to solidify into the slag;
8.Realize mechanical and electrical integration control, intelligent design of thermal control, low labor intensity;
9.Long service life of furnace lining, less wearing parts, low maintenance cost.

Product parameter introduction

Technical parameters/models

Heating capacity kJ/h

Coal consumptionkg/h

Furnace body dimension length × width × heightmm

Furnace body weight t (reference)

ZDFR-1

1 x4.18x106

143

4272x3228x4400

90

ZDFR-2

2x4.18x 106

286

4504x3460x4800

110

ZDFR-3

3x4.18x 106

429

4968x3924x5000

130

ZDFR-4

4x4.18x 106

571

5316x4156x5400

150

ZDFR-5

5x4.18x106

714

5784x4852x5600

180

ZDFR-6

6x4.18x10°

857

6016x4968x5800

200

ZDFR-8

8x4.18x 106

1143

6132x5780x6300

240

ZDFR-10

10x4.18x 106

1429

6480x6244x6800

270

ZDFR-12

12x4.18x106

1714

7060x6940x7100

300

ZDFR-14

14x4.18x 106

2000

7408x7404x7400

350

ZDFR-16

16x4.18x 106

2286

7520x7404x7800

400

ZDFR-18

18x4.18x106

2571

7980x6940x8600

420

ZDFR-20

20x4.18x10。

2857

8100x7170x8940

450

ZDFR-25

25x4.18x 106

3571

8330x7400x9360

500

ZDFR-30

30x4.18x 106

4286

8930x7656x10020

600

ZDFR-35

35x4.18x10'

5000

9140x7780x10500

750

Instructions for ordering


Installation precautions


Home

Home

News

News

About

About

Products

Products

Contact

Contact